智能新能源船舶的概念及关键技术

绿色和智能是当前船舶技术的发展趋势。文章首先提出了智能新能源船舶的概念,并介绍了智能新能源船舶的内涵、特点和系统构成;然后,从船舶航行、动力和推进3个方面分析了智能新能源船舶的关键技术;最后,对智能新能源船舶的未来发展进行展望。研究结果可为船舶的创新研究提供技术支持,引领船舶技术转型升级的发展方向。     

Influence of initial heeling angle on ship roll motion response北大核心CSCD

[目的]系统地研究初始横倾角对随机横浪下船舶横摇运动响应的影响。[方法]以路径积分法为基础,通过数值求解控制横摇运动微分方程概率属性的Fokker-Planck方程,得到横摇运动响应的概率分布。[结果]结果显示,初始横倾角对船舶横摇运动响应谱的影响有限,但对横摇角概率分布以及横摇运动响应极值分布的影响十分明显,且会造成船舶安全性的显著恶化。[结论]路径积分法可作为研究随机海浪下船舶横摇运动特性的有效数值方法。     

基于储能飞轮的电动汽车制动能量回收

飞轮储能具有绿色无污染的特点,发展潜能巨大。文章以电磁耦合式储能飞轮为研究对象,将其应用于纯电动汽车的制动能量回收,通过整车仿真,分析电磁耦合式储能飞轮的能量回收效率。建立搭载电磁耦合式储能飞轮系统的整车模型,并仿真验证,在初速度为70 km/h时,制动时间为5.853 s,制动距离为70.67 m。分别在不同初始速度和储能飞轮转动惯量条件下进行制动仿真。随着初速度提高,电磁转差离合器作用时间延长,飞轮储存能量增加,但储能飞轮的回收效率相差不大,且能量回收效率均不低于22.4%;转动惯量越大,回收的能量多,回收效率高,但制动时间增加,不利于行车的安全性。由此得出结论:电磁耦合式储能飞轮系统可以有效回收制动产生的能量,选择合适转动惯量的飞轮可以提高制动能量的回收效率。     

S^2 BHCA Multiple AUVs cooperation oriented control architecture

Oceanographic survey, or other similar applications should be the applications of multiple AUVs. In this paper, the skill ＆ simulation based hybrid control architecture （S^2BHCA） as the controller＇s design reference was proposed. It is a multi-robot cooperation oriented intelligent control architecture based on hybrid ideas. The S^2BHCA attempts to incorporate the virtues of the reactive controller and of the deliberative controller by introducing the concept of the ＂skill＂. The additional online task simulation ability for cooperation is supported, too. As an application, a multiple AUV control system was developed with three ＂skills＂ for the MCM mission including two different cooperative tasks. The simulation and the sea trials show that simple task expression, fast reaction and better cooperation support can be achieved by realizing the AUV controller based on the S^2BHCA.     

基于可视化界面的汽车平顺性分析及悬架参数选择

建立了含人体-座椅系统的前后轮两个路面输入的双轴汽车模型，以某款九座商务车为研究对象．分析了系统频域内与平顺性相关的输出量。利用Visual C＋＋编程，通过可视化界面实现了悬架参数的自由选择和复杂的计算分析过程，并且可直接输入整车参数得出仿真曲线，对汽车的平顺性进行有效地评价。     

先张法预应力空心板梁放张方法的探讨

传统的先张法预制空心板梁钢绞线的放张方法不能满足目前施工生产的需要,介绍一种对称切割钢绞线放张的施工工艺,保证了先张法预制梁板的施工质量。     

双相化处理工艺对冷拔双相钢丝组织和性能的影响

研究了08Mn2Si钢不同工艺处理后双相组织的形态及冷拔中组织与性能的变化,结果得到:950℃预淬火后再经临界区加热淬火时可以得到细小均匀的纤维状双相组枳,这种组织在冷拔中转变为很细的平行于拔丝方向的纤维状组织,且具有最好的强度和韧性。     

基于VTS的海事信息发布系统

此文论述了建立海事信息发布系统的必要性,并结合海上交通的发展,特别是VTS的使用, 提出了海事信息发布系统的总体结构和实现方式。实际应用表明,该系统能满足海事信息化、政务化和商务化的要求。     

A second order volume of fluid （VOF） scheme for numerical simulation of 2-D breaking waves

Among all environmental forces acting on ocean structures and marine vessels, those resulting from wave impacts are likely to yield the highest loads. Being highly nonlinear, transient and complex, a theoretical analysis of their impact would be impossible without numerical simulations. In this paper, a pressure-split two-stage numerical algorithm is proposed based on Volume Of Fluid (VOF) methodology. The algorithm is characterized by introduction of two pressures at each half and full cycle time step, and thus it is a second-order accurate algorithm in time. A simplified second-order Godunov-type solver is used for the continuity equations. The method is applied to simulation of breaking waves in a 2-D water tank, and a qualitative comparison with experimental photo observations is made. Quite consistent results are observed between simulations and experiments. Commercially available software and Boundary Integral Method (BIM) have also been used to simulate the same problem. The results from present code and BIM are in good agreement with respect to breaking location and timing, while the results obtained from the commercial software which is only first-order accurate in time has clearly showed a temporal and spatial lag, verifying the need to use a higher order numerical scheme.     

曲线钢轨抗磨耗损伤技术的应用

文章结合永安—漳平段线路钢轨现状调查,建立了抗磨损研究试验段,通过对试验结果分析,总结出减少钢轨鱼鳞损伤,以及机车轮缘磨耗的措施,为线路钢轨养护提供借鉴经验。